Review: Tube Audio Design TAD-60 Tube amp


Category: Amplifiers

I'll start by saying that I've been into higher-end audio for a few decades now, and quite a lot of equipment has been through my hands to this point (half the fun of this hobby). Somewhere around 12 years ago, I'd come to realize that I preferred tube amplification over solid state in terms of an overall involving presentation of the music, and ever since then have owned tube stuff (brief flirtations with various solid state devices only helped to enforce this notion).

Which brings me to the discovery of Tube Audio Design, the provider of components conceived by Paul Grzybek (of Bizzy Bee Audio fame), built to his specifications by a very reputable Chinese manufacturer, and then hand-finished by Paul in his shop located in Wheaton, IL. (His offerings are available exclusively online; detailed product info is found at http://www.angelfire.com/biz/bizzyb/index.html)

The TAD-60 amplifier is built like the proverbial tank; overall appearance and heft (not to mention its specifications) in my experience indeed belie the modest asking price. With its stainless steel chassis and almost 1/2"-thick black anodized face, the relatively compact package portrays a masculine but elegant stance (also included is a lift-off stainless steel tube cage). All function controls are easily accessible from the chassis top, as are the tube bias test-points and adjustment pots (a digital voltmeter is included too).

EL34-based, the TAD-60 is rated at 60wpc in UL-mode, and 30wpc in switchable-on-the-fly triode-mode. Other standard features include adjustable input sensitivity and adjustable global feedback, adding flexibility to a host of possible preamp and speaker combinations (the input sensitivity control may also be used as a volume pot in a single-source direct input configuration).

Listening to the TAD-60 after the recommended 30 hour break-in period and beyond, the music really began to open up, and along with the TAD-150 preamp, I was experiencing just about every CD I spun in a whole new manner - I'm particular to small-ensemble jazz and female vocals - there was an in-the-room conveyence of the music that I found startling at times - present is deep, tight bass, a glorious midrange, detail, depth, and an overall natural presentation that allows hour after hour of enjoyable listening. I've found that the feedback adjustment permits a fine-tuning of balance between dynamics and warmth, and was able to "lock in" the amp to my speakers for what sounds to be a perfect sonic match (just a tad of feedback along with the triode-mode setting seems to be the magic spot in my case).

Without attempting to describe every sonic attribute I'm hearing (though I'm happy to answer any particular inquiries), suffice it to say that the TAD-60/TAD-150 combination strikes a synergy and glow that is especially musical, and is among the finest I've had the pleasure of owning. The TAD-150 has already been highly praised in at least a few user and online reviews, and I bet the TAD-60 will soon be recognized as a similar standout. If you happen to be in the market for high quality, reasonably priced, excellent-sounding gear, just take a listen for yourself, and you will hear what these components can do for music. (Paul also offers a 15-day in-home trail period.)

Note: I have no financial interest or business relationship with Paul Grzybek or Tube Audio Design.

Associated gear
Magnepan 1.6QR, California Audio Labs CL-10, Music Hall MMF-5/Goldring G1012

Similar products
Conrad Johnson MV55
Sonic Frontiers SFS-40
VTL 50/50
Golden Tube SE-40
ASL AQ-1004
Sound Quest SQ-88
ggeers222
I am using KEF C75 speakers. They are 4 ohm speakers with a sensativity rating of 91db. No problem driving these speakers in PP UL or triode mode. In single ended mode (using only two power tubes instead of four) the amp couldn't drive these speakers at all. It had no problem with Klipsch Heresy though in single ended mode. The Heresy has a sensativity rating of 97db. I think the amp could drive most speakers with a moderate sensativity rating if used in PP mode. That leaves you a lot of speakers to audition. Happy hunting.
Interesting that you use MG 1.6 speakers...so do I. Some time ago I investigated whether I could use 60watt tube amps for my three MG1.6. In spite of the fact that my Maggies are crossed over from subwoofers, usually at about 80 Hz, voltage measurements at the speaker terminals revealed peaks that could only be achieved by a much more powerful amp. Mine are 600 watts into 4 ohms, and they just barely make it without clipping. Admittedly this was with very loud and challenging organ music, but that is sometimes what I listen to.

This TAD amp, and the model 1000 which would interest me appear to be excellent products at a very reasonable price. They remind me of the tube amps that I knew many years ago. However, the thought of the care and feeding of a dozen output tubes (for three TAD1000) puts me off! If I had a small system played softly these TAD amps would be in it.
I also wonder how the upcoming TAD 803 speakers would fare with the TAD 60/TAD 150 setup. From the info listed on Paul's site, it sounds pretty impressive for $499. I just can't get that B&W image out of my head for a long time. Maybe I wait a few more weeks and see if any new 803 owners will chime in as the shippments are being filled this month.

Thanks for the suggestions anyways.
Just rolled in a set of Electro-Harmonix KT-88s this weekend and the difference IMO was an overall improvement. The most noticeable difference was in increased headroom and a tighter more controlled bass. There was also a nice seperation of instruments in the highs and mids, a welcomed plus, because I love the sweet tone of the EL-34s but the KT-88s were right there as well. In general, I thought the EL-34 could muddy the bass a little when volume levels were cranked, where the KT-88 really held things together at high volumes. You know you've found a good thing when new things jump at you (in a good way) on familiar tunes that you couldn't zone in on before. Always brings a smile to my face. I was running the TAD-60 in tri-mode with the EL34s because I liked the warmth in the mid-range over the UL setting. However, I did like the extra power and dynamics UL provided, but I was constantly adjusting feedback to find that elusive level of warmth. With the KT-88s I have the TAD-60 set to UL mode now, with the feedback knob set at 2:30 and haven't felt the need to touch it once; its a perfect blend of warmth & dynamics that I couldn't achieve with the EL-34's. Tubes were purchased from the Tubedepot, they arrived in 2 days and were very helpful on the phone. However, 2 of them were running a little hot (715-720 range), so I freaked and called Paul, who was very good about walking me thru the setup, tubology 101, and assuring me that they would run fine. As you can probably tell, I'm new at this stuff, so it's nice to have a real pro to call when you need help.