Help, Strange Static Sound Recurring


I am a newbie. I have a nice hand-me-down system (from my Dad), a Jeff Rowland Model 1 Amp, an Audio Research LS3 preamp, Thiel 3.6 speakers, and if it matters, a Theta Data Basic with a Theta DS Pro Basic III.

When I set it up, it was fine. After a few weeks, I awoke to hear loud white noise (static) coming from one channel. I had left the system powered up, but the amp was off and the static persisted. I could not turn the amp on. When I would push the power button, it would light up, but would not "catch" and stayed unlit.

I called Rowland, and sent the unit in to them. It checked out perfectly. I hooked it up again and it was fine, only to repeat the problem. The Rowland people were flummoxed. They had played it continuously for a long time with no problem. I sent it off again, but no problem found.

I talked with a local (Minneapolis) audio guy who speculated that it could be that the power coming into my house is weak or inconsistent. I then tried a computer UPS (uninterruptible power source), and I thought the problem was solved, but alas it recurred.

Someone at one point mentioned that perhaps the 3.6's were a bit much for the amp, but he wasn't saying that was the cause.

At times I have unhooked the speaker cords, swapped channels, changed fuses, etc. Sometimes, unhooking and then reconnecting the speakers seems to make it work, but then after a few weeks, here comes the static again.

Anyway, it is frustrating and the wife wants me to sell the whole system. I just bluebooked it at 5K. I might do so, but I'd love to solve the problem.

Any thoughts? Anybody wanna buy it?
hyoster
Is there a Ham Radio operator operating nearby? I had a bad ground going to my system one time and with power turned off I could hear some static and bearly make out a voice. The Ham was totally legal in his transmissions and wnet ut of his way to help me find the bad ground.
Regarding possible service: I know an expert in Minneapolis area that may be able to assist you himself, or can refer you to someone else who can.
You guys are the best! I'm tied up tonight, but tomorrow will begin with the systematic experimentation.

I have never seen a group with such thoughtful advice on any subject. Again, I thank you for the technical and spousal advice.
Hy there's one other very basic issue that I forgot to mention, which could be the cause of this intermittent noise. We sometimes "look too deeply" into a technical problem, neglecting the basics which those of us that are more-experienced tend to take for granted.
This very basic issue is cable contact cleaning. As you are new to this, I'll explain again briefly here & then drop in the link to Galen Carol Audio's excellent website; under the "archives" section are many tech. tips that you should become more familiar with. Look over his whole website, read & learn a lot!
What happens over time is that your interconnect cable ends, panel-mounted equipment jacks, speaker cable connectors & ends attract dust, dirt, oils from skin contact, metallic oxidation occurs. This contamination causes (1) sonic degradation (2) possibly noisy connections esp. at the signal-interconnect level. One of the best & most popular contact cleaners is a product called Kontact, widely available, & one of Galen's favorites as well. If you're hesitant to spring for a $40 bottle of this "magic sauce" then at least get a small container of pure denatured alcohol from the drugstore; do not use isopropyl alcohol etc. as it contains lanolin, an oil which attracts dust right back into the connections, and water among other contaminants.
Cut some pipe cleaners into 1/3 sections & use those as your mildly abrasive applicators. Dip into the solvent & then scrub the cable connectors clean, both inside the contact point tips & around the shields. Also go around the outers & inners of your components' jacks, first ensuring that power is turned off. Also clean your AC cords, the mating female IEC's, speaker output posts, posts on the speakers themselves, & speaker cable ends. Change applicators when they become dirty looking & be sure to do that critical "second cleaning" as Galen explains all in great detail. If your intermittent noise is related to dirty contacts then this should fix that, & even if not then you'll still benefit from sonic improvements that can sometimes be dramatic in cases of gross neglect.
Here's that link:
http://www.gcaudio.com/Archives/howto.html
I took Bob's advise and cleaned all contacts with denatured alcohol. I plugged the amp back in and ... no power!

After checking around, I found a blue wire from the PC board on the side to one of the connectors on the back had become threaded between two speaker wire contacts. When I moved it, the amp powered up fine.

Then I hooked up everything else, and at least for now, the stereo sounds GREAT!!