Same thing happend to me years ago (60hz hum) and the answer was the Jensen transformer. I paid approx $50 and never looked back...
60 Hz Noise Reduction
How do I eliminate 60Hz hum from my audio system?
HISTORY:
I recently purchased an Acurus A200 to increase the volume level of the front channel of my second system. When I connected the unit I noticed a 60Hz hum coming from both front speakers. I'm thinking the new set up has created a ground loop, or the units with no AC ground plug (2 prong AC plug) have a floating ground. The 2 prong AC units are Denon AVR3805, and Velodyne ULD15. So I would like to get some ideas of things I can do to eliminate the 60Hz hum This set up is a hodge podge of equipment left overs from the past.
OLD SET-UP (No 60Hz Noise)
Denon AVR3805 driving front, center, and surround speakers.
Denon preamp out to ULD15 controller/amp driving ULD15 sub.
NEW SET-UP (60Hz Noise)
Denon AVR3805 reciever which powers center, and surround speakers which are Monitor Audio bookshelf speakers. Denon pre-amp out to ULD15 Series II controller/amp driving Velodyne ULD15 sub. ULD RCA output to Acurus A200 amp input driving Monitor Audio GS10 for front.
Ideas Appreciated
Aaron
HISTORY:
I recently purchased an Acurus A200 to increase the volume level of the front channel of my second system. When I connected the unit I noticed a 60Hz hum coming from both front speakers. I'm thinking the new set up has created a ground loop, or the units with no AC ground plug (2 prong AC plug) have a floating ground. The 2 prong AC units are Denon AVR3805, and Velodyne ULD15. So I would like to get some ideas of things I can do to eliminate the 60Hz hum This set up is a hodge podge of equipment left overs from the past.
OLD SET-UP (No 60Hz Noise)
Denon AVR3805 driving front, center, and surround speakers.
Denon preamp out to ULD15 controller/amp driving ULD15 sub.
NEW SET-UP (60Hz Noise)
Denon AVR3805 reciever which powers center, and surround speakers which are Monitor Audio bookshelf speakers. Denon pre-amp out to ULD15 Series II controller/amp driving Velodyne ULD15 sub. ULD RCA output to Acurus A200 amp input driving Monitor Audio GS10 for front.
Ideas Appreciated
Aaron
- ...
- 10 posts total
no cable box just TiVo.Where does the TiVo receive its signal from? I think I nailed it by attaching earth ground to Denon Receivers chassis ground. Not a good idea. If the Denon has a two wire polarized plug that means the equipment was designed and manufactured with double insulated ac power wiring, therefore an equipment ground (third wire) is not used. An earth ground connected to the chassis could degrade the sonics of the unit. More than likely the signal ground of the unit is connected to the chassis. By earth grounding the chassis EMI/RFI AC noise could enter the electronics of the unit through the ground wire. Jensen VRD-1FF http://www.jensen-transformers.com/datashts/vrd1ff_manual.pdf |
Denon Chassis Ground yes the Denon has 2 prong polarized AC plug. I'm assuming that if I connect the chassis to AC ground instead of earth ground it would cause the same EMI/RFI noise problem. or worse correct? I ordered the Jensen ISOMAX CI-2RR, and will install, and remove the earth ground from the Denon reciever chassis. TiVo/Cable Loop The Cable TV, and TiVo coxial are not connected to the Denon unit. However from these treads I'm going to connect the coxial cable through the isolation coax line in the Panamax power management system. Thanks Again Aaron |
- 10 posts total